The Foundation of Plumbing Skills for Bathtub Installation
The Foundation of Plumbing Skills for Bathtub Installation
Blog Article
Have you been hunting for insight about A Step-by-Step Guide to Installing a Bathtub?
Mounting a bath tub isn't specifically rocket science, however it does require strong plumbing, woodworking, and often, tiling abilities. Replacing an old tub with a brand-new one is also a reasonably tough job. If the old tub is readily easily accessible, the job can move rapidly; if you need to open up a wall to eliminate the old bathtub and place the new bath tub, the job is a lot harder. In either case, the project is within a house handyman's skills, although you will certainly need a helper to vacate the old bathtub and set in the new one. See to it you have certified yourself for the task and are comfortable attempting it. Rather than hiring a professional to take control of a halfway-completed task, it is far better to think about using one prior to you start. Chances are you might need a specialist plumber to make tube links.
This short article will certainly help you install a brand-new tub in your restroom if you have currently acquired a new bathtub and do not require to change the arrangement of your previous water system pipes.
Your devices and product list should comprise the following:
Removing Old Touches
If you require to change old taps with new ones as a part of your installation, after that the first thing you need to do is separate the water. After doing so, switch on the taps to drain pipes any kind of water staying in the system. The procedure of eliminating the existing taps can be fairly bothersome due to the restricted access that is often the instance.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipes to the taps. Have a towel prepared for the continuing to be water that will certainly come from the pipelines. As soon as the supply pipes have been eliminated, make use of the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will need to stop the solitary taps from turning during this process. When the faucets have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing substance.
Prior to going on to fit the brand-new taps, contrast the pipeline connections on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new faucets to fit.
Suitable New Taps
If the tails of the new taps are plastic, then you will certainly require a plastic connector to prevent damage to the string. One end of the connector fits on the plastic tail of the tap and the various other end offers a link to the existing supply pipelines.
If you need to fit a monobloc, after that you will certainly require decreasing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, place the faucet in the installing opening in the bath/basin guaranteeing that the washers remain in area in between the faucet as well as the sink. Safeguard the tap in position with the manufacturer given backnut. Once the faucet is securely in place, the supply pipes can be linked to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with typical tap connectors. The previous kind should be attached to the tap finishes first, tightening up only by hand. The supply pipelines can later on be attached to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Installing the Bathtub
Making use of the two wood boards under its feet, place the bathtub in the needed placement. The wooden boards are useful in evenly spreading out the weight of the tub over the area of the boards rather than concentrating all the weight onto four tiny points.
The next objective is to ensure that the bath tub is leveled all round. This can be accomplished by checking the spirit level and adjusting the feet on the tub till the level reads degree.
To mount faucets, fit all-time low of the furthest flexible faucet adapter to the appropriate supply pipe by making a compression join; after that do the very same for the other tap.
Activate the water supply as well as examine all joints and new pipework for leaks and also tighten them if required. Fill up the tub and likewise inspect the overflow electrical outlet and the typical outlet for leakages.
Finally, deal with the bathroom paneling as defined in the maker's user's manual. Tiling as well as securing around the bath tub needs to wait until the bathtub has been used at the very least once as this will resolve it into its final setting.
Getting ready for the Installment
To start with, the sustaining frame supplied with the bathroom needs to be fitted (if called for) according to the manufacturer's directions. Next, fit the faucets or mixer to the tub. When fitting the tap block, it is very important to see to it that if the faucet includes a plastic washing machine, it is fitted in between the bath as well as the faucets. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets system to avoid stress on the tub.
Fit the adaptable faucet connectors to the bottom of the two faucets making use of 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Ensure you utilize every one of the provided washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link all-time low of the overflow tube in a similar manner.The bath ought to now be ready to be suited its last placement.
Tiling Around the Bath tub
In the area where the bathroom meets the ceramic tile, it is required to secure the accompanies a silicone rubber caulking. This is essential as the fitting can move sufficient to fracture a rigid seal, creating the water to pass through the wall in between the bathroom and also the tiling, causing complications with dampness and feasible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to assimilate your components and also fittings. They are marketed in tubes and also cartridges, and also are capable of sealing spaces up to a size of 3mm (1/8 inch). If you have a bigger space to load, you can load it with spins of drenched paper or soft rope. Bear in mind to always fill the bathtub with water before securing, to permit the activity experienced when the bathtub remains in use. The sealant can split rather early if you do not consider this activity prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also easily readily available on the marketplace. It is a good idea to fit the ceramic tiles making use of waterproof or water resistant sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you really like reading up on Tools You Need to Install a New Bathtub ? Make feedback down below. We would be pleased to listen to your suggestions about this write up. We hope that you come back again in the future. So long as you liked our blog post if you please don't forget to pass it around. Thank you for your time invested reading it.
Visit The Following Page Report this page